Skip Navigation: Avoid going through Home page links and jump straight to content
NASA Logo - Jet Propulsion Laboratory    + View the NASA Portal
Search Stardust  
JPL Home Earth Solar System Stars & Galaxies Technology
Stardust Banner
Overview Mission Science Technology Newsroom Education Gallery Links Stardust Home
 
Aerogel
Instruments
Deep Space Network
Stardust Microchip
Additional Technologies


tech_addInfo_left.gif

Aerogel Fact Sheet (PDF - 2.9 MB)

More photos of aerogel are available in our Photo Gallery.

See also our Frequently Asked Aerogel Questions.

guinnesscert_150.jpg
Guinness Records Names JPL's Aerogel World's Lightest Solid

 

For additional technical information about aerogel see, Berkeley National Laboratory .

 

 


tech_aerogel.gif
tech_comet_dust.gif

trk-s.jpg  

Particle captured in Aerogel

 
The primary objective of the Stardust mission is to capture both cometary samples and interstellar dust. Main challenges to accomplishing this successfully involve slowing down the particles from their high velocity with minimal heating or other effects that would cause their physical alteration. When the Stardust Spacecraft encounters the Comet Wild 2, the impact velocity of the particles will be up to 6 times the speed of a rifle bullet. Although the captured particles will each be smaller than a grain of sand, high-speed capture could alter their shape and chemical composition - or even vaporize them entirely.

To collect particles without damaging them, Stardust uses an extraordinary substance called aerogel. This is a silicon-based solid with a porous, sponge-like structure in which 99.8 percent of the volume is empty space. By comparison, aerogel is 1,000 times less dense than glass, which is another silicon-based solid. When a particle hits the aerogel, it buries itself in the material, creating a carrot-shaped track up to 200 times its own length. This slows it down and brings the sample to a relatively gradual stop. Since aerogel is mostly transparent - with a distinctive smoky blue cast - scientists will use these tracks to find the tiny particles.
 
tech_aero_capabilites.gif

aerogelcrayons_s.jpg  

Crayons on Aerogel over a flame

 
Aerogel is not like conventional foams, but is a special porous material with extreme microporosity on a micron scale. It is composed of individual features only a few nanometers in size. These are linked in a highly porous dendritic-like structure.

This exotic substance has many unusual properties, such as low thermal conductivity, refractive index and sound speed - in addition to its exceptional ability to capture fast moving dust. Aerogel is made by high temperature and pressure-critical-point drying of a gel composed of colloidal silica structural units filled with solvents. Aerogel was prepared and flight qualified at the Jet Propulsion Laboratory (JPL). JPL also produced aerogel for the Mars Pathfinder and Stardust missions, which possesses well-controlled properties and purity. This particular JPL-made silica aerogel approaches the density of air. It is strong and easily survives launch and space environments. JPL aerogel capture experiments have flown previously and been recovered on Shuttle flights, Spacelab II and Eureca.

 
tech_tennis.gif

atlotray6_s.jpg  

Aerogel Dust Collector under construction.

 

The aerogel aboard the Stardust Spacecraft is fitted into a "tennis racket" shaped collector. This is unfolded from the protective Sample Return Capsule to expose it to space during flight. One side of the collector will be faced towards the particles in Comet Wild 2, while the reverse, or B side, will be turned to face the streams of interstellar dust encountered during its journey.

When hypervelocity particles are captured in aerogel they produce narrow cone-shaped tracks that are hollow, and can easily be seen in the highly transparent aerogel by using a stereomicroscope. This cone is largest at the point of entry, and the particle is held intact at the point of the cone. This provides a method for determining which direction the dust came from, and is the basis of the approach of using single slabs of aerogel to collect both cometary and interstellar dust from both sides.

After the encounter with Comet Wild 2, the aerogel collector will be retracted into the Sample Return Capsule (SRC) and returned to Earth for detailed analysis by scientists at the NASAs Johnson Space Center.

 

Last updated March 31, 2005

tech_quick_facts.gif

aerogelhand_s.jpg

It is 99.8% Air

Provides 39 times more insulating than the best fiberglass insulation

Is 1,000 times less dense than glass

Was used on the Mars Pathfinder rover

 

 

 

 

 
     
 
Privacy F.A.Q. Contact Sitemap Credit
 
FIRST GOV + Freedom of Information Act
+ The President's Management Agenda
+ FY 2002 Agency Performance and accountability report
+ NASA Privacy Statement, Disclaimer, and Accessiblity Certification
+ Freedom to Manage
NASA Home Page Site Manager:
Aimee Whalen

Webmaster:
Ron Baalke

http://www.jpl.nasa.gov http://www.nasa.gov http://www.caltech.edu/